Low-Profile U-Shaped Scissor Lift Table | Pitless Pallet Jack Lift | Gradin

Eliminating concrete floor pit excavation across cleanroom packing cells and assembly bays, this low-profile scissor lift table positions palletized freight at ergonomic waist heights. The 85 mm collapsed stature allows hand pallet trucks and automated guided vehicles to roll unit loads straight into the open-center deck without approach ramps.

• Safe Working Load (SWL): 1,500 kg (100% rated capacity; 125% static proof test verified)
• Collapsed Profile: 85 mm base datum; zero pit digging required
• Elevation Stroke: 800 mm vertical rise in 20 to 25 seconds
• Deck Interface: Open-center U-cradle matched to manual pallet trucks

Why Work With GRADIN

  • Rapid Response: Expert engineering consultation from day one.
  • Proven Process: Precision from initial concept to final client approval.
  • Quality Assurance: Documented manufacturing, inspection and pre-shipment testing.
  • Factory-Direct Engineering: Direct communication with the engineering and manufacturing team.
  • Lifetime Support: Technical assistance for the product’s entire operational lifespan.
Specification & Configuration
Engineering Metric Base Production Baseline ETO Configurable Envelope Safety Compliance & Standards
Safe Working Load (SWL) 1,500 kg (3,307 lbs) 500 kg to 3,000 kg 125% proof tested; EN 1570-1 / ANSI MH29.1
Collapsed Platform Height 85 mm (3.35 in) pitless 75 mm to 105 mm collapsed profile Surface mount; zero pit excavation
Vertical Travel Stroke 800 mm (31.5 in) 600 mm to 1,200 mm stroke Limit switches with hard positive stops
Deck Geometric Profile U-Shaped open-center deck Solid flat, U-Shape, E-Shape decks Laser-cut EN 10025-2 S355JR plate steel
Overall Deck Footprint 1,450 x 1,150 mm outer 1,000 x 800 mm to 2,200 x 1,600 mm Engineered to Euro, GMA, or skid profiles
Fork Cutout Dimension 585 mm (Euro pallet trucks) 585 mm (Euro) or 780 mm (GMA / US) Ramp-free ground level wheel-in access
Hydraulic Actuation Twin external cylinders Dual or quad synchronized cylinders Velocity safety fuses on cylinder ports
Power Skid Configuration Remote 2.2 kW hydraulic unit 1.5 kW to 5.5 kW remote power skids Braided hoses with drip-free couplings
Perimeter Safety Device Aluminum contact safety edge Contact trip edge or optical curtains EN 1570-1 compliant downward travel cutoff
Control Interface Hold-to-run pendant console Floor pedals, wall pulpit, PLC links IP55 / NEMA 4 enclosure; E-stop palm switch
Fully Customizable: Dimensions and configurations can be tailored to your specific site requirements.
Features

Product Features: Low-Profile Scissor Lift Architecture

Low-Profile Chassis in Certified EN 10025-2 S355JR Structural Steel

Solid steel scissor arms formed from high-tensile EN 10025-2 S355JR plate distribute torsional stress across high-cycle operations. The 85 mm collapsed profile rests flush on existing factory concrete slabs, avoiding moisture accumulation traps common to subterranean floor pits. Precision pivot eyes house self-lubricating DU composite bushings on induction-hardened pivot pins, preventing joint play under eccentric loads.

Dual Synchronized Displacement Cylinders with Isolated Hydraulic Power Skid

Twin external push cylinders drive the open-center scissors through mechanical linkage pivots. The independent 2.2 kW hydraulic power skid isolates motor heat, fluid reservoirs, and pump vibration from clean assembly airspaces via high-pressure flexible braided lines with quick-disconnect couplers. Velocity fuses threaded straight into cylinder supply ports seal hydraulic fluid inside cylinder barrels if lines burst.

Open-Center U-Deck Geometry for Ramp-Free Pallet Jack Access

The open interior cavity accommodates standard pallet truck forks, allowing operators to deposit Euro and industrial skids flush onto the deck wings from floor grade. Operators position pallets on side load runners and raise workpieces to part-dispensing heights, eliminating lumbar bend during repetitive bin-picking tasks.

Aluminum Perimeter Anti-Pinch Safety Frame with Hold-to-Run Controls

A full-perimeter aluminum contact edge surrounds the lower deck flange, tripping limit sensors to arrest downward travel if workers contact floor obstructions. A standalone IP55 push-button console incorporates dual-channel hold-to-run (deadman) controls, a twist-release emergency stop palm button, and mechanical maintenance blocks to lock raised scissor arms during servicing.

Application scenarios

Clean Industrial & Ergonomic Assembly Applications

Cleanroom Pallet Material Dispensing Without Floor Excavation

Semiconductor packaging cells and clean pharmaceutical staging lines exclude floor pits to avoid dirt traps and chemical pooling. The 85 mm lowered height allows manual stainless pallet trucks to wheel product containers into position at floor level before lifting for ergonomic part dispensing.
• [Permissible Load Eccentricity]: ±100 mm offset center under 1,500 kg gross weight
• [Facility Hygiene Compatibility]: Continuous weld seams, non-shedding hydraulic lines, IP55 enclosure
• [Floor Installation Standard]: Surface mount on level epoxy-coated concrete slabs without excavation

Ergonomic Workstation Sub-Assembly and Bin Staging

Automotive transmission and wire harness builders maintain components at constant waist level throughout work shifts. Continuous height control eliminates spinal fatigue, while the open-center cutout lets assemblers walk deep into the load zone without leaning across wide table decks.
• [Cantilever Load Bearing]: Up to 50% rated payload supported on single platform side wings
• [Operational Duty Cycle]: High-cycle manufacturing duty up to 40 lift cycles per hour
• [Operator Interface]: Heavy-duty foot pedal switches with safety foot guard covers

Video Demonstration
PRODUCT DETAILS & WORKSHOP PHOTOS
Global Standards Compliance
GRADIN OEM/ODM CUSTOMIZATION & DELIVERY POLICY

For this heavy-duty series, we can engineer load capacities up to [300] tons, with platform dimensions and lifting heights customized to your operational envelope. Requirements exceeding our standard engineering matrix will undergo a Finite Element Analysis (FEA) by our engineering team to ensure structural viability before proposing a solution.

To initiate the engineering proposal, please provide the following baseline data:

  • Rated Load Capacity

  • Maximum Lifting Height & Closed Height

  • Platform Dimensions (L x W)

  • Duty Cycle (e.g., operational cycles per hour/day)

  • Environmental Conditions (e.g., indoor/outdoor, washdown, explosion-proof)

  • Pit depth or overhead clearance constraints

Yes. The control systems can be equipped with standard communication protocols (e.g., Profinet, Modbus, Ethernet/IP) utilizing [Siemens / Allen-Bradley / Omron] PLCs. This ensures seamless I/O signal synchronization with upstream/downstream conveyors, AGV/AMR units, and your central control room.

Every custom unit undergoes a mandatory Factory Acceptance Test (FAT) prior to dispatch. This includes continuous operational testing at 100% rated load, static overload testing at [120% / 125%] capacity, and the physical triggering of all mechanical anti-fall and hydraulic safety interlocks. FAT documentation and video proof are included in your engineering package.

Upon final approval of the General Arrangement (GA) drawings, the manufacturing lead time is typically 4 to 8 weeks. Oversized structural components are engineered with a modular design to fit into standard shipping containers (20FT/40HQ). On-site assembly utilizes pre-engineered bolted flange connections and heavy-duty aviation plugs, strictly eliminating the need for field welding.

We provide a standard [12/24]-month warranty covering the structural frame and primary hydraulic/electrical components. To minimize operational downtime, a comprehensive set of standard consumables (e.g., cylinder seal kits, travel switches, relays) is shipped alongside your equipment. During the warranty period, replacement parts for non-human-induced failures are dispatched via priority air freight (DHL/FedEx) within 48 hours.

Beyond the warranty, we guarantee lifetime engineering support. Your custom equipment's CAD drawings, electrical schematics, and BOM (Bill of Materials) are permanently archived in our system. This ensures you receive uninterrupted remote troubleshooting, maintenance guidance, and exact spare parts matching for the entire lifecycle of the equipment.

Related Upenders & Material Handling Solutions

Get a Bespoke Engineering Proposal

🔒 Your project information is kept confidential. Our engineering team will respond within 24 hours to discuss your requirements and next steps.